Zetasizer sample preparation for reliable DLS and zeta potential measurements

color samples, trend colors, interior design, interior-design, judgement, decision, layout, inneneinrichter, interior architect, painter, wall gestalter, to dye, color circle, paint brush, color theory, itten, interior design, interior design, interior design, interior design, interior design, layout, interior architect, painter, color theory, color theory

What Zetasizer sample preparation should achieve

Zetasizer sample preparation is not just a step before analysis. It largely determines whether dynamic light scattering and zeta potential results describe the original dispersion or an artefact introduced during handling. A useful sample is representative, optically suitable, chemically unchanged and free from dust, bubbles and visible debris. For DLS size measurements, the preparation should let particles diffuse freely and scatter enough light without multiple scattering. For zeta potential, it must preserve the particle surface and the liquid chemistry that controls the electrical double layer.

In routine work, this means controlling concentration, dispersant composition, filtration, temperature, cell cleanliness and the order of mixing. For related workflow notes, see the sample preparation section.

dough, flour, knead, bake, loaf, yeast, kitchen, chef, baker, dough, flour, knead, yeast, yeast, chef, baker, baker, baker, baker, baker

Start with the measurement goal, not the instrument

A Zetasizer can be used for several light-scattering measurements, and each places different demands on the sample. Dynamic light scattering, often called DLS, estimates hydrodynamic particle size from Brownian motion. Electrophoretic light scattering, used for zeta potential, measures electrophoretic mobility and then calculates zeta potential through an appropriate model. Static light scattering may also be used in some workflows, although most routine preparation questions concern DLS size and zeta potential.

The first decision is therefore not simply whether to filter, sonicate or dilute. It is what the measurement is meant to answer. If the goal is native aggregate state, harsh sonication may remove the information of interest. If the goal is primary particle size after dispersion, controlled sonication or another defined dispersion step may be justified. If the goal is zeta potential in a formulation, dilution into pure water may make the sample easier to measure while changing the chemistry being measured.

Measurement Main preparation risk Practical priority
DLS particle size Dust, aggregates, multiple scattering and incorrect viscosity Clean dispersant, suitable concentration and stable temperature
Zeta potential Dilution that changes pH, ionic strength or additive balance Preserve the original medium or dilute with matched supernatant
Highly scattering samples Detector overload, particle-particle interactions and non-free diffusion Check a dilution series rather than relying on one concentration
Weakly scattering samples Low signal, dirty cells and high background from solvent or cuvette Use clean optical cells and verify the blank before measuring

Control concentration before changing analysis settings

Concentration is a common source of inconsistent Zetasizer data. Malvern Panalytical guidance for Zetasizer method development notes that every sample has its own useful concentration range. Too little material may give insufficient scattered light. Too much material can cause multiple scattering, where light scattered by one particle is scattered again by another. It can also introduce particle-particle interactions that prevent free diffusion.

For DLS size measurements

For DLS, a clearer sample is not automatically a more accurate one. Excessive dilution may reduce signal or destabilize a dispersion. Insufficient dilution may shift the apparent size because of multiple scattering or particle interactions. A practical approach is to prepare a small dilution series in the same dispersant and compare whether reported size, polydispersity and correlogram quality remain consistent across reasonable concentrations. If the apparent size changes strongly with dilution, concentration may be the cause, but the change may also indicate altered dispersion chemistry.

ISO 22412:2025, the current dynamic light scattering standard, emphasizes that DLS test samples should be well dispersed in a liquid medium and that preparation procedures such as sonication and filtration can influence the result and should be reported. For routine laboratories, this is a critical point: a DLS number without a preparation history is difficult to reproduce, even when the same instrument model is used.

For zeta potential measurements

Zeta potential preparation is less forgiving because the result depends on both the particle surface and the surrounding liquid. Malvern Panalytical guidance on zeta potential dilution stresses that the purpose of dilution is to preserve the existing surface state. When a concentrated dispersion must be diluted, the preferred strategy is often to separate clear liquid from the original sample by filtration or centrifugation and use that supernatant as the diluent. This keeps the balance of dissolved ions, unbound additives, surfactants or polymers closer to the original system.

If supernatant cannot be obtained, the next best option is usually to match the medium as closely as possible in pH, total ionic concentration and additive content. Diluting a formulation into deionized water may produce a convenient measurement, but it can also change the electrical double layer and produce a zeta potential value that no longer represents the formulation.

Prepare the dispersant as carefully as the particles

The dispersant is part of the measurement system, not just a carrier liquid. ISO 22412:2025 describes the suspension liquid for DLS as needing to be transparent at the laser wavelength, low in particulate contamination, non-fluorescent, chemically compatible with the particulate material and sufficiently defined for refractive index and viscosity to be known. These requirements affect scattering intensity, hydrodynamic size calculation and the ability to distinguish sample particles from background noise.

Blank checks and filtration

Before adding the sample, measure or at least inspect the dispersant blank according to the laboratory method. A high or unstable background can point to contaminated solvent, dust, flare from the cell wall or a dirty cuvette. Filtering the dispersant is usually safer than filtering the complete sample, because sample filtration can remove real large particles or aggregates and bias the size distribution. If the sample must be filtered, record the membrane material and pore size, and interpret the result as the filtered fraction rather than automatically as the original dispersion.

Viscosity, refractive index and temperature

DLS converts diffusion behavior into hydrodynamic diameter through temperature- and viscosity-dependent relationships. A viscosity value copied from pure water is not suitable for every buffer, solvent blend, polymer solution or formulation. ISO 22412:2025 requires the suspension liquid to have a known viscosity over the temperature range used. For routine work, this means equilibrating the sample at the measurement temperature, using the correct dispersant file or method settings, and avoiding warm hands, cold storage carryover or rapid solvent evaporation immediately before a run.

Use dispersion steps that can be repeated

Sonication, vortex mixing, inversion, rolling, centrifugation and sedimentation can improve one sample and damage another. The outcome depends on material hardness, aggregate strength, surface chemistry and the question being asked. Gentle inversion may be enough for a stable nanoparticle dispersion. A powder dispersed into liquid may need wetting, staged addition and controlled energy input. Protein, polymer and emulsion samples may be more sensitive to heat, foaming or shear. See also: buying guides.

Make each dispersion step specific enough to repeat. Instead of recording only sonicated before measurement, record the sonication type, time, power setting if available, bath temperature control and rest time before measurement. If centrifugation is used to remove dust or large debris, record speed, time, rotor type where relevant and whether the supernatant or pellet was measured. If sedimentation is used for zeta potential, state how long the sample was left and which fraction was taken.

Preparation should also avoid creating a false sense of monodispersity. Removing visible flocs may be appropriate when they are contaminants, but not when the aim is to understand formulation instability. The method should match the decision that the data will support.

Fill the cell without adding artefacts

A well-prepared dispersion can still fail at the cell-filling stage. Dust on the outside wall, fingerprints on optical windows, scratches in plastic cuvettes, trapped bubbles and residues from previous samples can all produce misleading scattering. Reusable glass or quartz cells are useful for weakly scattering samples, but only if they are cleaned consistently and are compatible with the solvent. Disposable cells reduce carryover risk, although they can be scratched or chemically attacked by some organic solvents.

For DLS cuvettes, avoid touching optical faces and inspect the filled cell for bubbles and visible particles. For folded capillary zeta cells or similar zeta potential cells, filling technique matters because bubbles in the measurement path can interrupt the electric field and scatter light. Slow loading, compatible syringes or pipette tips, and a short visual inspection are often more effective than repeating several failed measurements.

Cell compatibility is especially important for non-aqueous samples, surfactant-rich liquids and aggressive solvents. A solvent that softens plastic can increase background or release contaminants. A sample that adsorbs strongly to the wall may show changing results during repeated measurements. If the result drifts between runs, do not only adjust analysis settings; consider whether the sample is interacting with the cell.

A practical workflow for routine laboratories

  1. Define the measurement question: native state, dispersed state, formulation comparison or stability screen.
  2. Select the dispersant and record its composition, pH where relevant, viscosity, refractive index and temperature.
  3. Check the blank for low and stable background before measuring weak or critical samples.
  4. Prepare the sample using a documented sequence of mixing, dilution, filtration, sonication or centrifugation.
  5. For DLS, test whether size results are stable across a reasonable concentration range.
  6. For zeta potential, dilute with original supernatant where possible, or match pH, ionic strength and additives as closely as practical.
  7. Fill the cell carefully, remove bubbles, clean optical surfaces and allow temperature equilibrium.
  8. Review data quality indicators, repeatability and physical plausibility before reporting the result.
Observed issue Likely preparation cause Corrective check
Large unexpected size peak Dust, bubbles, flocs or contaminated dispersant Run blank, inspect cell and repeat with clean dispersant
Size changes after dilution Multiple scattering, particle interactions or chemistry shift Run a dilution series in matched dispersant
Zeta potential changes strongly with diluent Changed pH, ionic strength or additive concentration Use supernatant or a better matched medium
Low signal or noisy data Too little sample, weak scatterer or high cell background Increase concentration cautiously and verify cell cleanliness
Run-to-run drift Temperature change, aggregation, adsorption or settling Equilibrate temperature and check time dependence

Frequently asked questions

Should all Zetasizer samples be filtered before DLS?

No. Filtering the dispersant is often useful, but filtering the sample can remove large particles, aggregates or droplets that may be part of the material being characterized. If filtration is used, report the filter material and pore size and make clear that the result applies to the filtered sample.

Can I dilute zeta potential samples with deionized water?

Only when that dilution represents the question being asked. For many dispersions, deionized water changes ionic strength, pH and additive balance. A better approach is to use clear supernatant from the original sample or a medium matched for pH, ionic concentration and additives.

How do I know whether my DLS sample is too concentrated?

Signs include poor data quality, inconsistent apparent size after dilution, unusually high scattering, or results that change with measurement position or attenuation behavior. A dilution series prepared in the same dispersant is usually more informative than a single run.

Does sonication always improve Zetasizer results?

No. Sonication can disperse loose agglomerates, but it can also heat the sample, change fragile particles, break droplets or alter protein and polymer systems. Use controlled conditions and report the method whenever sonication affects the result.

What should be reported with a Zetasizer result?

Report the measurement type, dispersant composition, temperature, viscosity setting, concentration or dilution factor, cell type, preparation steps, filtration or centrifugation conditions and any observation of instability. These details often explain differences between laboratories better than instrument model alone.